UNDERSTANDING ESSENTIAL PLUMBING SKILLS IS ESSENTIAL FOR INSTALLING A BATHTUB

Understanding Essential Plumbing Skills is Essential for Installing a Bathtub

Understanding Essential Plumbing Skills is Essential for Installing a Bathtub

Blog Article

Visit My Site

This great article following next relating to How to Install a Bathtub is particularly interesting. Give it a try and make your own personal findings.


Tools You Need to Install a New Bathtub
Installing a bathtub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bathtub with a new one is additionally a moderately difficult task. If the old bathtub is easily easily accessible, the project can relocate immediately; if you need to open up a wall surface to remove the old tub as well as position the brand-new bathtub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make sure you have qualified on your own for the job and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed project, it is better to consider utilizing one before you begin. Chances are you may need an expert plumber to make tube connections.
This write-up will help you mount a new tub in your shower room if you have already bought a brand-new tub as well as do not require to alter the arrangement of your previous water supply pipelines.
Your devices and also product list ought to make up the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain pipes any water staying in the system. The process of eliminating the existing faucets can be fairly problematic because of the restricted gain access to that is often the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipelines. As soon as the supply pipes have been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
    Before going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end gives a link to the current supply pipelines.
    If you need to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next, position the faucet in the installing hole in the bath/basin making certain that the washing machines remain in area in between the faucet as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be linked to the tap finishes first, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Setting up the Bathtub


    Using the two wood boards under its feet, position the tub in the required setting. The wood boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little factors.
    The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bathtub till the level reads level.
    To install faucets, fit the bottom of the outermost adaptable tap port to the suitable supply pipeline by making a compression join; then do the same for the other tap.
    Activate the water and examine all joints and brand-new pipework for leakages and tighten them if needed. Fill the bathtub and likewise inspect the overflow electrical outlet and the regular outlet for leakages.
    Finally, fix the bath paneling as defined in the supplier's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the tub has actually been utilized at least when as this will certainly settle it right into its final placement.

    Getting ready for the Installment


    Firstly, the supporting framework supplied with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps system to stop stress on the bathtub.
    Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its last setting.

    Tiling Around the Bathtub


    In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in problems with wetness and feasible leakages to the ceiling below.
    You can select from a variety of coloured sealers to blend in your components as well as fittings. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealer can fracture fairly early if you do not take into account this activity before securing.
    Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water-proof sticky and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    We hope you liked our excerpt about Installing A Bathtub. Many thanks for spending some time to browse our article post. Do you know about someone else who is interested by the niche? Do not hesitate to promote it. Thanks a lot for your time spent reading it.


    Click Here To Find Out More

    Report this page